Perencanaan Perawatan Pada Unit Kompresor Tipe Screw Dengan Metode RCM di Industri Otomotif

Agustinus Dwi Susanto(1*), Hery Hamdi Azwir(2),

(1) 
(2) President University
(*) Corresponding Author
DOI: https://doi.org/10.23917/jiti.v17i1.5380

Abstract

Production process at PT. Showa Indonesia Manufacturing is not always smooth, due to the ignorance of the reliability of the machine. Breakdown can occur at any time and cause uncertainty of the availability of machinery in the production process, causing considerable losses to the company. This study was conducted on a compressor machine used to produce the pressurized air that used to run the production machinery. Based on the research, the highest damage level is on the compressor machine 4, 8, 10, 5, 16, and 6 with total damage of 70.1%. This is due to the complex machine system and the less optimal maintenance system. Reliability Centered Maintenance (RCM) method is used to analyze the system to identify components that fall within the critical category. The results of the analysis, obtained some critical components which required optimal replacement interval by minimizing downtime. Further planning activities on each critical component is based on FMEA and RCM Decision Worksheet. With the application of RCM method, total downtime decreased by 44.59% from previous preventive actions.

 

Keywords

Breakdown, Reliability Centered Maintenance, Age Replacement, FMEA, RCM Decision Worksheet, Downtime.

References

Ebeling, E.C. (1997). An Introduction To Reliability and Maintainability Engineering. New York: McGraw-Hill Inc.

Felecia. (2014) “Fuzzy Logic Reliability Centered Maintenance.” Jurnal Teknik Industri, Vol. 16 (2), 121-126.

Hidayah, N.Y.; Ahmadi, N. (2017). Analisis Pemeliharaan Mesin Blowmould Dengan Metode RCM Di PT. CCAI. Jurnal Optimasi Sistem Industri 16, no. 2: 167. https://doi.org/10.25077/josi.v16.n2.p167-176.2017.

Kurniawati, D.A.; Muzaki, M.L. (2017). “Analisis Perawatan Mesin Dengan Pendekatan RCM Dan MVSM.Jurnal Optimasi Sistem Industri 16 (2), 89-105.

Masruroh, N. (2008). Perencanaan Kegiatan Perawatan Pada Unit Produksi Butiran (padat) Dengan Basic: RCM (Reliability Centered Maintenance) Di PT Petrokimia Kayaku Gresik. Skripsi, UPN”Veteran”, Indonesia.

Moubray, J. (1991). Reliability Centered Maintenance (RCM II). Great Britain: Butterworth-Heinemann Ltd.

Rachman, H.; Garside, A.K.; Kholik, H.M. (2017). “Usulan Perawatan Sistem Boiler Dengan Metode Reliability Centered Maintenance (RCM)”. Jurnal Teknik Industri, Vol. 18 (1), 86-93.

Sari, D.P.; Ridho, M.F. (2016). “Evaluasi Manajemen Perawatan Dengan Metode Reliability Centered Maintenance (Rcm) II Pada Mesin Blowing I Di Plant I Pt. Pisma Putra Textile”. Jurnal Teknik Industri, Vol. 11 (2), 73–80.

Sudrajat, A. (2011). Pedoman Praktis Manajemen Perawatan Mesin Industri. Bandung: Refika Aditama.

Article Metrics

Abstract view(s): 5897 time(s)
PDF (Bahasa Indonesia): 9644 time(s)

Refbacks

  • There are currently no refbacks.