THE EFFECTS OF PACK CARBURIZING USING CHARCOAL ON PROPERTIES OF MILD STEEL

Supriyono Supriyono(1*)

(1) Universitas Muhammadiyah Surakarta
(*) Corresponding Author

Abstract

The aim of this research is to study the effects of pack carburizing using charcoal on properties of mild steel. The properties are represented by the results of microstructure, hardness test and tensile test.  The carburizing process was conducted in the temperature of 930oC which is the austenite temperature of the mild steel. The source of carbon was charcoal. The specimens were held for 2, 3 and 4 hours at the carburizing temperature. The carbon content of the raw amterial was 0.17%. The raw material was hypoeutectoid steel with ferrite and pearlite phases in its microstructure.  After the carburizing process, the microstructure can be divided into two zones e.i. case zone and core zone. The case zone consists of hypereutectoid, eutectoid, and hypoeutectoid sub-zone. The core zone is the same as raw material. The longer the holding time will result in the deeper the case zone and the stronger the material.

Full Text:

PDF

References

J. K. Ahmad, “Carburizing of steel,” Int. J. Mater. Sci. Appl., vol. 4, pp. 11–14, 2015.

F. O. Aramide, S. A. Ibitoye, I. O. Oladele, and J. O. Borode, “Pack carburization of mild

steel, using pulverized bone as carburizer: Optimizing process parameters,” Leonardo

Electron. J. Pract. Technol., vol. 9, no. 16, pp. 1–12, 2010.

A. Oyetunji and S. O. Adeosun, “Effects of Carburizing Process Variables on Mechanical

and Chemical Properties of Carburized Mild Steel,” J. Basic Appl. Sci., vol. 8, pp.

–324, 2012.

A. P. Ihom, G. B. Nyior, O. O. Alabi, S. Segun, J. Nor Iv, and J. Ogbodo, “The Potentials

of Waste Organic Materials for Surface Hardness Improvement of Mild,” Int. J. Sci.

Eng. Res., vol. 3, no. 11, pp. 1–10, 2012.

P. B. D. D. Swapnil R. Nimbhorkar, “Effect of Case Hardening Treatment on the

Structure and Properties of Automobile Gears,” Int. J. Mod. Eng. Res., vol. 3, no. 2, pp.

–641, 2013.

S. Priyadarshini, T. Sharma, and G. Arora, “Effect of Post Carburizing Treatment on

Hardness of Low Carbon Steel,” Int. J. Adv. Mech. Eng., vol. 4, no. 7, pp. 763–766, 2014.

Supriyono and Jamasri, “Holding time effect of pack carburizing on fatigue characteristic

of v-notch shaft steel specimens,” in AIP Conference Proceedings, 2017, vol. 1855.

D. A. Okongwu and V. Paranthaman, “Assesment of The Efficacy of Some Carbonate

Minerals as Energizers in Pack Carburisation of Mild Steel,” Niger. J. Technol., vol. 11,

no. 1, 1987.

H. C. ASM, Metals Handbook, 8th ed. Ohio, 1972.

Y. Lakhtin, Engineering Physical Metallurgy. Moscow: Foriegn Language Publishing

House, 1965.

DOI: 10.23917/mesin.v19i1.5812

Article Metrics

Abstract view(s): 824 time(s)
PDF: 1966 time(s)

Refbacks

  • There are currently no refbacks.