Flexural Capacities and Stress Block Parameters for High-Strength Concrete Column

A Antonius(1*)

(1) Universitas Sultan Agung
(*) Corresponding Author

Abstract

Flexural behaviour of reinforced high-strength concrete columns is studied in this paper. Tests of 12 high-strength reinforced concrete columns under eccentric loading were conducted, with test parameters included the concrete strength, longitudinal reinforcement ratio, load eccentricities and lateral reinforcement characteristics i.e: spacing and volumetric ratio. Concrete strength used were around of 50 and 70 MPa. From this study, the main result shows that curvature ductility increase with increasing volumetric ratio or reduction of tie spacing for lateral reinforcement. Comparison between stress block parameter models developed by many researchers with the test results was evaluated. It is found that the model adopted in the Indonesian National Standard (SNI 03-2847-2002) and ACI need to be modified before they can be utilized in the flexural design of structures made of high-strength concrete.

Full Text:

PDF

References

ACI Committee 318 (2005), ―Building code requirements for

structural concrete (ACI 318-05) and commentary (318R05)‖, American Concrete Institute, Farmington Hills, MI,

pp.430.

Antonius (2011), ―Confinement effects on high-strength

concrete columns subjected eccentric loading‖,

Proceeding of The 4th ASEAN Civil Engineering

Conference, Yogyakarta, Indonesia, 22-23 Nov., pp.21-26.

Antonius (2004), ―The influence of lateral reinforcement to

the cover spalling mechanisms of high strength concrete

column structures‖, Proc. of National Conference of

Earthquake Eng. II, Gajah Mada Univ., Indonesia, pp.168-

, (in Indonesian).

Attard, M.M. and M.G. Steward (1998), ―A two parameter

stress block for high-strength concrete‖, ACI Structural

Journal, V.95 (3), pp.305-317.

Bae, S. and O. Bayrak (2003), ―Stress block parameters fo

high-strength concrete members‖, ACI Structural Journal,

V.100 (5), pp. 626-636.

CEB-FIP (2008), Constitutive Modelling of High

Strength/High Performance Concrete; State of the Art

Report, January.

Foster, S.J. and M.M. Attard (1997), ―Experimental tests on

eccentrically loaded high-strength concrete columns, ACI

Structural Journal, V.94 (3), pp.295-303.

Indonesian National Standard (2002), Computational Method

of Reinforced Concrete Structures for Building, SNI-03-

-2002 (in Indonesian).

Ibrahim, H.H.H. and J.G. MacGregor (1997), ―Modification of

the ACI rectangular stress block for high-strength

concrete‖. ACI Structural Journal, V.94 (1), pp.40-48.

Mertol, H.C., S. Rizkalla, P. Zia, and A. Mirmiran (2008),

―Characteristics of compressive stress distribution in highstrength concrete‖, ACI Structural Journal, V.105 (5),

pp.626-633.

Steward, M.G. and M.M. Attard (1999), ―Reliability and

model accuracy for high-strength concrete column

design‖, Journal of. Struct. Eng. ASCE, V.125 (3), pp.

-300.

Teng-Hooi, Tan and Ngoo-Ba Nguyen (2005), ―Flexural

behavior of confined high-strength concrete columns‖,

ACI Structural Journal, V.102 (2), pp.198-205.

DOI: 10.23917/dts.v12i3.18808

Article Metrics

Abstract view(s): 104 time(s)
PDF: 80 time(s)

Refbacks

  • There are currently no refbacks.